bending point的例句大全

The material mechanical properties, such as flexural strength, are measured by three point bending techniques.

利用三点弯曲方法测定了材料的抗弯强度等力学性能.

Upper body bending front, leg point raising, heel touching ground.

上身前倾, 腿尖抬高, 腿跟着地.

A special machine with scanning electron microscope ( SEM ) used was designed for three point bending test.

设计了一种可用扫描电镜 ( SEM ) 动态观察、专门用于三点弯曲试验的特殊装置.

Through bending experiment, adhesive materials failure point and load of toughened and not toughened samples are analyzed and the toughening modification of adhesive materials can improve the adhesive properties between CFRP and concrete.

通过弯曲试验，分析粘结材料增韧前后弯曲试件的破坏特点和破坏载荷，得出对粘结材料进行增韧改性可以提高CFRP与混凝土的粘结性能。

For uniform isotropic materials, bending modulus of three point bending ( TPB) test and four point bending ( FPB) test are almost the same and they are almost equal to material ′ s tensile modulus.

对于均质各向同性材料，三点弯曲实验和四点弯曲实验得到的弯曲模量与拉伸模量基本上一致。

Testing method for annealing point and strain point of glass by beam bending

玻璃退火点和软化点测定方法-压梁法

The quasi-static three-point bending behavior of square aluminum extrusions with aluminum foam filler is studied.

研究了泡沫铝填充的方形铝管的准静态三点弯曲行为.

This paper introduces Four-point bending method recognized in the World and its application.

介绍了国际上公认的四点弯曲法试验的受力特,点和应用.

An effective three-point bending test based on compound beam theory is introduced.

介绍了利用复合梁理论测量高速电弧喷涂层弹性模量的方法.

A method to solve tension softening relationship of concrete obtained a three-point bending test is presented.

确立了分别基于开裂强度准则和断裂韧性准则的由三点弯曲实验确定混凝土材料抗拉软化关系的方法.

The experiment determined the fracture process and the parameter of the fracture properties of two different aggregate concrete and recorded the stable whole fracture curves of boulder concrete and crushed stone concrete separately, which are determined through three-point-bending method and wedge-split tensile method.

测定了两种粗骨料混凝土的断裂过程及断裂特征参数，分别记录了两种试验方法测定的卵石混凝土和碎石混凝土的断裂全曲线。

The specimens of boulder concrete and crushed stone concrete were tested through three-point-bending method and wedge-split-tensile method.

对卵石、碎石混凝土试件进行了三点弯曲试验和楔入劈拉试验。

It is investigated that the influence of Bauschinger Effect on yield strength of tube body by using four point bending test to simulate the tube making process at varying stress strain amplitudes.

采用X65钢板在四点弯曲加载条件下，模拟输油管制管过程中不同应变量下的应力&应变过程，研究包申格效应对输油管管体屈服强度的影响。

As the bending strength of sodium silicate sand cured by ester method is much higher than that cured by CO_2 method the analysis shows that the key point is the refinement of grains of silicate gel.

分析了酯法比CO2法水玻璃砂强度高的原因，指出充分发挥水玻璃粘结效率的关键在于细化水玻璃凝胶胶位。

In this paper, we established a wormlike chain ( WLC) model with variable local persistence length to study polymer molecules with different bending stiffness at each point.

本文针对链上各点处弯曲刚度不同的聚合物分子，建立了变持续长度蠕虫链（WLC）模型。

In this paper, the finite element method based on GTN model is used to investigate the ductile crack growth behavior in the three-point bending specimens of the dissimilar metal welded joint.

本文采用内嵌GTN损伤模型的有限元方法，建立了核电异种金属焊接接头三点弯曲试样的有限元模型，数值模拟延性裂纹的起裂和扩展行为。